IKEYCUTTER Condor XC-007 key cutting machine Tech Support

Q: When install update tool, the system warns can not find FTD2XX.dll file?
A: You have to install the software driver first.

Q: How can I access into "Factory Mode"?
A: Power off the XC-007 key cutting machine Press both the right up button and left up button at the same time, and then click the "Factory Mode" button on the right bottom corner..

Q: How to install XC007 key cutting software driver?
A: 1) Download software driver (ft232.zip driver) and unzip it
2) Connect Condor XC-007 main device with computer via USB cable, power up the device
3) Wait the system to find the new driver. Save file to certain folder and install the driver.

Q: How to update XC-007 Condor software?
A: Download software update tool and follow the system prompts.
Free download Condor XC-007 software here: Ikeycutter Condor XC-007 Free Download & Service (hyperlinks) http://www.cnblogs.com/sinoy/p/4159639.html

Q: How can I know when to update XC-007 software?
A:. Run software update tool, it will display the newest software version and update notice Check the current software version in XC-007 main program.

Q: Must I update the XC-007 software to latest version?
A: Run update tool and check the new function added in new version If the new functions meet your need or helps fix some problem, run software update..
 
Q: How to calibrate XC-007 touch screen?
A: Touch anywhere on touch screen, power on the device, followed by clicking the cross center.

Q: What‘s the difference between "Direct processing" and "Start processing"?
A: "Direct Processing": - process the key directly according to the teeth depth directly without any modification If the original key is broken, the new keys will be broken as well..

"Start processing": - according to the tooth depth to calculate the nearest standard tooth depth, and then use the repaired standard teeth to process, it is helpful for repairing worn keys.

Q: When do I need to do "ATC height leveling"?
A: You need to do "ATC height leveling" every time you got the cutter or probe replaced.

Q: When do I need to do "X1, X2 clamp initialization"?
A: X1, X2 clamp should be initialized only once when you get the XC007 key cutting machine You can do it again if you feel it is not correct..

Q: When using the X3 clamp to cutting key, why it is out of use when the probe encountered the clamp?
A: The problem main due to the low the cutter or the probe height Increase the height of the cutter and probe and then do "Cutter probe height leveling" after raising height..

Q: How to calibrate if the cutting key overall shifts horizontally?
A: 1): Re-start X1 and X2 initialization
2): Enter "Factory Mode", do the "Duel probe calibration" (or "Cutting Calibration")
3): Cut TOY43, full No. 1 tooth
4): Enter into the "Factory Mode", follow the prompts to adjust PDx parameters slightly.

Q: How to calibrate the cutting key if the key Z-axis deviation goes wrong?
A: 1): Install X1 clamp, enter into the "Device initialization" to do "Cutter probe height leveling".
2): Enter "Device initialization" to do "X1 Initialization"
3): Install X2 clamp, enter "Device initialization" to do "X2 Initialization"

Q: The key groove width milling out wrong?
A: If the width is narrow, decrease Dm in "Factory Mode"; if the width is wide, increase Dm in "Factory Mode".

Q: What should I enter after get the Peugeot, Citroen code?
A: 1) Enter into the database, all input
2) If not, enter into the database, enter the last 6 number of the code
3) If not, enter into the database, enter the middle 6 number and add 1 number, like: XX1XXXX

Q: What‘s the corresponding teeth number of Japanese car INSY?
A: Japanese
I = ichi = 1
N = ni = 2
S = san = 3
Y = yon = 4

Q: When carry out duel probe calibration, the system warns "more than 30 Alice" how to do?
A: Replace the cutter into probe, you need to install 2 probes when do Duel probe calibration.