pcDuino的linux移植四简单驱动开发

浏览数：54 / 时间：2015年06月20日

开发环境
系统：ubuntu 10.04.4
单板：pcDuino(全志A10)
编译器：arm-2009q3-67-arm-none-linux-gnueabi-i686-pc-linux-gnu.tar.bz2

搭建开发环境详见ubuntu 10.04.4开发环境配置。

目标
1.配置编译linux-3.0.62内核,串口正常输出
2.配置内核,支持nfs挂载,启动文件系统
3.最简单内核驱动开发

这个是在pcDuino linux移植一、二、三的基础上写的，重点介绍内核驱动开发，其它具体移植过程不再详述。最基础的裸板开发、u-boot移植以及linux移植，参考前面的文章，这里不再重复。

一、搭建驱动开发平台

这里用官方提供的源码kernel for pcduino,我试了哈，这里面有些常用的驱动，比如网卡驱动之类，在官方提供的kernel平台再添加自己的驱动。

1.准备工作

获取交叉编译器http://code.google.com/p/smp-on-qemu/downloads/list选择arm-2009q3-67-arm-none-linux-gnueabi-i686-pc-linux-gnu.tar.bz2并下载。然后在ubuntu下直接解压即可，配置过程还不清楚的看Ubuntu 10.04.4开发环境配。

获取linux源码 https://github.com/pcduino/kernel 点击linux-sunxi,跳转到https://github.com/linux-sunxi/linux-sunxi下载linux-sunxi源码

2.配置、编译内核

打开linux-sunxi-sunxi-3.0目录下的Makefile,修改195：

ARCH ?= ARM

CROSS_COMPILE ?= your-path/arm-2009q3/bin/arm-none-linux-gnueabi-

其中your-path是gcc-linaro-arm-linux-gnueabihf-4.8-2013.04-20130417_linux.tar.bz2的解压路径

change @change :~$ cd /home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0/
change @change :~/Si/A10/pcduino/linux-sunxi-sunxi-3.0$ make menuconfig

记住选中wemac support(A1x),其它不变。开始也不知道选这个，后来分析官方提供的kernel才知道的。

编译过程超长，如果编译过程中遇到些问题，见pcduino linux 移植一、二、三

change@change:~/Si/A10/pcduino/linux-sunxi-sunxi-3.0$ ls arch/arm/boot
bootp compressed Image install.sh Makefile uImage zImage

3.测试

经过pcDuino linux移植一、二、三，我们已制作一张可启动的tf卡，现在用我们新的内核uImage,替换掉以前的进行测试。将上次制作的启动卡插到PC机，弹出窗口，直接拷贝上面编译生成的uimage到sdb1，替换掉以前的，取下tf卡插到pcduino启动如下：

U-Boot SPL 2012.10 (Apr 19 2013 – 18:46:44)
DRAM: 1024MB
SUNXI SD/MMC: 0
U-Boot 2012.10 (Apr 19 2013 – 18:46:44) Allwinner Technology

CPU: SUNXI Family
Board: pcDuino
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
*** Warning – bad CRC, using default environment

In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
reading uEnv.txt

144 bytes read
Loaded environment from uEnv.txt
reading boot.scr

270 bytes read
Jumping to boot.scr
## Executing script at 44000000
reading script.bin

” from mmc 0:1 ** “script.bin
reading uImage

” from mmc 0:1 ** “uImage
bootm – boot application image from memory

Usage:
bootm [addr [arg ...]]
- boot application image stored in memory
passing arguments ‘arg …’; when booting a Linux kernel,
‘arg’ can be the address of an initrd image

Sub-commands to do part of the bootm sequence.  The sub-commands must be
issued in the order below (it’s ok to not issue all sub-commands):
start [addr [arg ...]]
loados  – load OS image
cmdline – OS specific command line processing/setup
bdt    – OS specific bd_t processing
prep – OS specific prep before relocation or go
go    – start OS
reading script.bin

44900 bytes read
reading uImage

4693140 bytes read
## Booting kernel from Legacy Image at 48000000 …
Image Name: Linux-3.0.62
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4693076 Bytes = 4.5 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum … OK
Loading Kernel Image … OK
OK

Starting kernel …

<6>Initializing cgroup subsys cpuset
<5>Linux version 3.0.62 (change@change) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #2 PREEMPT Tue May 21 22:35:22 CST 2013
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: sun4i
<6>Memory cut off:
<6>    MALI : 0x5c000000 – 0x5fffffff  (  64 MB)
<4>Ignoring unrecognised tag 0×00000000
<6>Memory Reserved:
<6>    SYS  : 0×43000000 – 0x4300ffff  (  64 kB)
<6>    VE : 0×44000000 – 0x48ffffff  (  80 MB)
<6>    G2D  : 0×49000000 – 0x49ffffff  (  16 MB)
<6>    LCD  : 0x5a000000 – 0x5bffffff  (  32 MB)
Memory policy: ECC disabled, Data cache writeback
<6>chip-id: A10 (AW1623 revision C)
<7>On node 0 totalpages: 245760
<7>free_area_init_node: node 0, pgdat c0887ea0, node_mem_map c094e000
<7>  Normal zone: 1280 pages used for memmap
<7>  Normal zone: 0 pages reserved
<7>  Normal zone: 146176 pages, LIFO batch:31
<7>  HighMem zone: 768 pages used for memmap
<7>  HighMem zone: 97536 pages, LIFO batch:31
<7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 243712
<5>Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=8 panic=10
<6>ID hash table entries: 4096 (order: 2, 16384 bytes)
<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Memory: 448MB 512MB = 960MB total
<5>Memory: 833852k/833852k available, 149188k reserved, 393216K highmem

……….//省略若干，太长了

<6>mmc0: new high speed SD card at address 0260
[ 4.070000] mmc0: new high speed SD card at address 0260
<6>mmcblk0: mmc0:0260 SD 948 MiB
[ 4.090000] mmcblk0: mmc0:0260 SD 948 MiB
<6> mmcblk0: p1 p2
[ 4.100000] mmcblk0: p1 p2
<6>Console: switching to colour frame buffer device 160×45
[ 4.230000] Console: switching to colour frame buffer device 160×45
<4>regulator_init_complete: axp20_buck3: incomplete constraints, leaving on
[ 4.270000] regulator_init_complete: axp20_buck3: incomplete constraints, leaving on
<4>regulator_init_complete: axp20_buck2: incomplete constraints, leaving on
[ 4.290000] regulator_init_complete: axp20_buck2: incomplete constraints, leaving on
<4>regulator_init_complete: axp20_ldo4: incomplete constraints, leaving on
[ 4.300000] regulator_init_complete: axp20_ldo4: incomplete constraints, leaving on
<4>regulator_init_complete: axp20_ldo3: incomplete constraints, leaving on
[ 4.320000] regulator_init_complete: axp20_ldo3: incomplete constraints, leaving on
<4>regulator_init_complete: axp20_ldo2: incomplete constraints, leaving on
[ 4.330000] regulator_init_complete: axp20_ldo2: incomplete constraints, leaving on
<4>regulator_init_complete: axp20_ldo1: incomplete constraints, leaving on
[ 4.350000] regulator_init_complete: axp20_ldo1: incomplete constraints, leaving on
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[ 4.360000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
<6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:9
[ 4.370000] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:9
<6>sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:00:09 UTC (1262304009)
[ 4.380000] sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:00:09 UTC (1262304009)
<3>EXT3-fs (mmcblk0p2): error: couldn’t mount because of unsupported optional features (240)
[ 4.400000] EXT3-fs (mmcblk0p2): error: couldn’t mount because of unsupported optional features (240)
<3>EXT2-fs (mmcblk0p2): error: couldn’t mount because of unsupported optional features (244)
[ 4.420000] EXT2-fs (mmcblk0p2): error: couldn’t mount because of unsupported optional features (244)
<6>EXT4-fs (mmcblk0p2): recovery complete
[ 4.740000] EXT4-fs (mmcblk0p2): recovery complete
<6>EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.750000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
<6>VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 4.770000] VFS: Mounted root (ext4 filesystem) on device 179:2.
<6>devtmpfs: mounted
[ 4.780000] devtmpfs: mounted
<6>Freeing init memory: 164K
[ 4.790000] Freeing init memory: 164K
mount: mounting devpts on /dev/pts failed: No such file or directory
mount: mounting /dev/mmcblk0p1 on /boot failed: No such file or directory

Please press Enter to activate this console.

Processing /etc/profile… Done

/ # ls
bin    etc    lib    mnt    run    sys    usr
dev    home    linuxrc  proc    sbin    tmp    var
/ # ifconfig eth0 172.16.1.111
<4>wemac wemac.0: WARNING: no IRQ resource flags set.
[  126.910000] wemac wemac.0: WARNING: no IRQ resource flags set.
<6>wemac wemac.0: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[  127.060000] wemac wemac.0: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
/ # <7>eth0: no IPv6 routers present
[  137.860000] eth0: no IPv6 routers present

/ # ifconfig eth0
eth0    Link encap:Ethernet  HWaddr 8A:CA:EF:97:41:11
inet addr:172.16.1.111  Bcast:172.16.255.255  Mask:255.255.0.0
inet6 addr: fe80::88ca:efff:fe97:4111/64 Scopeink
UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
RX packets:20 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:6831 (6.6 KiB)  TX bytes:468 (468.0 B)
Interrupt:55 Base address:0×8000

/ # ping 172.16.1.134
PING 172.16.1.134 (172.16.1.134): 56 data bytes
64 bytes from 172.16.1.134: seq=0 ttl=64 time=11.119 ms
64 bytes from 172.16.1.134: seq=1 ttl=64 time=1.628 ms
64 bytes from 172.16.1.134: seq=2 ttl=64 time=0.866 ms
^C
— 172.16.1.134 ping statistics —
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.866/4.537/11.119 ms
/ #

看到系统基本正常启动了，网卡工作也正常能ping通。先写到这里，下一步做简单驱动开发，待续。。。并且已支持挂载，以后把自己编译好的驱动挂载到单板pcduino,在手动加载到单板，然后写个简单应用程序，测试驱动。最后再编译进内核。我是想搭建这么个驱动开发平台。

二、最简单内核驱动开发

1.编写代码

写一个最简单的驱动程序，介绍驱动开发流程。先写字符一个简单的字符驱动代码：first_drv.c

[plain] view plain copy

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/fs.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <asm/uaccess.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <mach/gpio.h>
#include <mach/hardware.h>
#include <linux/device.h>
static struct class *firstdrv_class;
static struct class_device *firstdrv_class_dev;
static int first_drv_open(struct inode *inode, struct file *file)
{
printk(“first_drv_open\n”);
return 0;
}
static ssize_t first_drv_write(struct file *file, const char __user *buf, size_t count,loff_t *ppos)
{
printk(“first_drv_write\n”);
return 0;
}
static struct file_operations first_drv_fops ={
.owner = THIS_MODULE,
.open = first_drv_open,
.write = first_drv_write,
};
int major;
static int first_drv_init(void)
{
major = register_chrdev(0, ”first_drv”, &first_drv_fops);
firstdrv_class = class_create(THIS_MODULE, ”firstdrv”);
firstdrv_class_dev = device_create(firstdrv_class,NULL,MKDEV(major, 0), NULL, ”xyz”);
return 0;
}
static void first_drv_exit(void)
{
unregister_chrdev(major,”first_drv”);
device_unregister(firstdrv_class_dev);
class_destroy(firstdrv_class);
}
module_init(first_drv_init);
module_exit(first_drv_exit);
MODULE_LICENSE(“GPL”);

编写Makefile:

[plain] view plain copy

KERN_DIR = /home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0
all:
make -C $(KERN_DIR) M=`pwd` modules
clean:
make -C $(KERN_DIR) M=`pwd` modules clean
rm -rf modules.order
obj-m += first_drv.o

其中KERN_DIR是你的内核源码存放路径，要根据自己情况修改。

2.编译驱动源码

change@change:~/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv$ make
make -C /home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0 M=`pwd` modules
make[1]: Entering directory `/home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0′
CC [M]  /home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv/first_drv.o
/home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv/first_drv.c: In function ‘first_drv_init’:
/home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv/first_drv.c:38: warning: assignment from incompatible pointer type
/home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv/first_drv.c: In function ‘first_drv_exit’:
/home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv/first_drv.c:45: warning: passing argument 1 of ‘device_unregister’ from incompatible pointer type
include/linux/device.h:692: note: expected ‘struct device *’ but argument is of type ‘struct class_device *’
Building modules, stage 2.
MODPOST 1 modules
CC    /home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv/first_drv.mod.o
LD [M]  /home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv/first_drv.ko
make[1]: Leaving directory `/home/change/Si/A10/pcduino/linux-sunxi-sunxi-3.0′
change@change:~/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv$ ls
firstdrivetest.c  first_drv.ko    first_drv.mod.o  Makefile    Module.symvers
first_drv.c    first_drv.mod.c  first_drv.o    modules.order
change@change:~/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv$

可以看到生成了驱动加载模块first_drv.ko,下面还要写个简单的驱动测试代码firstdrivetest.c：

[plain] view plain copy

#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <stdio.h>
int main(int argc, char **argv)
{
int fd;
int val = 1;
fd = open(“/dev/xyz”, O_RDWR);
if(fd < 0)
{
printf(“can’t open!\n”);
}
write(fd, &val, 4);
return 0;
}

接着编译驱动测试代码

change@change:~/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv$ /home/change/tools/arm-2009q3/bin/arm-none-linux-gnueabi-gcc -o firstdrivetest firstdrivetest.c
change@change:~/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv$ ls
firstdrivetest first_drv.c first_drv.mod.c first_drv.o modules.order
firstdrivetest.c first_drv.ko first_drv.mod.o Makefile Module.symvers
change@change:~/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv$

先拷到我的主机nfs挂载目录，不知道怎么配置看ubuntu 10.04.4开发环境配置

change@change:~/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv$ cp first_drv.ko firstdrivetest /home/change/work/rootfs_dir/fs_mini/home/linux-3.0.62/pcduino/
change@change:~/Si/A10/pcduino/linux-sunxi-sunxi-3.0/drivers/mydrv$

记住编译驱动、根文件系统、内核的交叉编译器最好用同一套编译器，不然会出现问题，我又遇到过。看到测试驱动的firstdrivetest也生成了。下面将其挂载到到你的单板pcduino进行测试。现在切换到单板pcduino启动的控制台进行挂载

/ # mount -t nfs -o nolock 172.16.1.134:/home/change/work/rootfs_dir/fs_mini /mn
t/
/ # ls /mnt/
bin etc lib mnt root sys usr
dev home linuxrc proc sbin tmp
/ # cd /mnt/home/linux-3.0.62/pcduino/
/mnt/home/linux-3.0.62/pcduino # ls
first_drv.ko firstdrivetest
/mnt/home/linux-3.0.62/pcduino #

看到挂载成功了，刚刚我们编译生成的first_drv.ko firstdrivetest也挂载到单板了。测试先加载驱动

/mnt/home/linux-3.0.62/pcduino # ls /dev/xyz
ls: /dev/xyz: No such file or directory
/mnt/home/linux-3.0.62/pcduino # insmod first_drv.ko
/mnt/home/linux-3.0.62/pcduino # ls /dev/xyz -l
crw——- 1 0 0 245, 0 Jan 1 00:52 /dev/xyz
/mnt/home/linux-3.0.62/pcduino #

可以看到加载前是不存在这个xyz设备的，成功加载后出现了。再运行测试程序，测试程序很简单就是驱动加载成功则输出first_drv_open、first_drv_write

/mnt/home/linux-3.0.62/pcduino # ./firstdrivetest
first_drv_open
[ 3297.090000] first_drv_open
first_drv_write
[ 3297.090000] first_drv_write
/mnt/home/linux-3.0.62/pcduino #

运行firstdrivetest ，与预期效果一致，基本正常。但是后来发现还有问题，如下不能卸载驱动

/mnt/home/linux-3.0.62/pcduino # lsmod
first_drv 1473 0 – Live 0xbf000000
/mnt/home/linux-3.0.62/pcduino # rmmod first_drv
rmmod: can’t change directory to ‘/lib/modules’: No such file or directory
/mnt/home/linux-3.0.62/pcduino # rmmod first_drv.ko
rmmod: can’t change directory to ‘/lib/modules’: No such file or directory
/mnt/home/linux-3.0.62/pcduino #

遇到问题，跟着提示做，没有’/lib/modules’那新建一个

/mnt/home/linux-3.0.62/pcduino # mkdir /lib/modules
/mnt/home/linux-3.0.62/pcduino # rmmod first_drv
rmmod: can’t change directory to ’3.0.62′: No such file or directory

又出现没有’3.0.62′，再创建一个

/mnt/home/linux-3.0.62/pcduino # mkdir /lib/modules/3.0.62
/mnt/home/linux-3.0.62/pcduino # rmmod first_drv
/mnt/home/linux-3.0.62/pcduino # lsmod
/mnt/home/linux-3.0.62/pcduino #

OK这下解决了，我以前又遇到过，发现这么解决最简单，再完整测试一遍

/mnt/home/linux-3.0.62/pcduino # ./firstdrivetest
first_drv_open
[ 3841.960000] first_drv_open
first_drv_write
[ 3841.970000] first_drv_write
/mnt/home/linux-3.0.62/pcduino # rmmod first_drv
/mnt/home/linux-3.0.62/pcduino # lsmod
/mnt/home/linux-3.0.62/pcduino #

问题基本解决了，我们的驱动开发平台就搭建好了，以后抓紧写其它驱动代码。还试了一下rmmod first_drv.ko 卸载不了，还是要用rmmod first_drv

/mnt/home/linux-3.0.62/pcduino # insmod first_drv.ko
/mnt/home/linux-3.0.62/pcduino # lsmod
first_drv 1473 0 – Live 0xbf008000
/mnt/home/linux-3.0.62/pcduino # rmmod first_drv.ko
/mnt/home/linux-3.0.62/pcduino # lsmod
first_drv 1473 0 – Live 0xbf008000
/mnt/home/linux-3.0.62/pcduino # rmmod first_drv
/mnt/home/linux-3.0.62/pcduino # lsmod
/mnt/home/linux-3.0.62/pcduino #

测试完使用halt停机

/mnt/home/linux-3.0.62/pcduino # halt
The system is going down NOW!
Sent SIGTERM to all processes
Terminated
Sent SIGKILL to all processeso #
Requesting system halt<6>[sw-ohci2]: shutdown start
[ 4290.610000] [sw-ohci2]: shutdown start
[sw-ohci2]: close clock
[ 4290.620000] [sw-ohci2]: close clock
<6>[sw-ohci2]: shutdown end
[ 4290.620000] [sw-ohci2]: shutdown end
<6>[sw-ehci2]: shutdown start
[ 4290.630000] [sw-ehci2]: shutdown start
[sw-ehci2]: Set USB Power OFF
[ 4290.640000] [sw-ehci2]: Set USB Power OFF
[sw-ehci2]: close clock
[ 4290.640000] [sw-ehci2]: close clock
<6>[sw-ehci2]: shutdown end
[ 4290.650000] [sw-ehci2]: shutdown end
<6>[sw-ohci1]: shutdown start
[ 4290.660000] [sw-ohci1]: shutdown start
[sw-ohci1]: close clock
[ 4290.660000] [sw-ohci1]: close clock
<6>[sw-ohci1]: shutdown end
[ 4290.670000] [sw-ohci1]: shutdown end
<6>[sw-ehci1]: shutdown start
[ 4290.680000] [sw-ehci1]: shutdown start
[sw-ehci1]: Set USB Power OFF
[ 4290.690000] [sw-ehci1]: Set USB Power OFF
[sw-ehci1]: close clock
[ 4290.690000] [sw-ehci1]: close clock
<6>[sw-ehci1]: shutdown end
[ 4290.700000] [sw-ehci1]: shutdown end
[NAND]shutdown
[ 4290.710000] [NAND]shutdown
nand try to shutdown 0 time
[ 4290.710000] nand try to shutdown 0 time
Nand flash shutdown ok!
[ 4290.720000] Nand flash shutdown ok!
<0>System halted.
[ 4290.720000] System halted.